NDA Ammo and Reloading Component TRADE thread



SupressYourself

Founding Member
Founding Member
Thread starter
Joined
Apr 21, 2015
Posts
2,012
Likes
420
Points
333
Location
Not where I'd like to be
I have one Box of Hornady 6.5 143 gr ELD M. They are not for sale,I want to trade for ELD X 143 gr. Trade bullet for bullet.

I assume you mean 140 ELDM, and I assume you mean a box of 100. If so, I have 153 count of the 143 ELDX. If you'd send me like $10 to cover my shipping, I'd trade you 153 of my 143s for 100 of your 140s.

Full disclosure: my 143s are mixed lots, but have been weight sorted with 109 of them falling between 142.8 and 143.1 grains.
 

Big Iron

Founding Member
Founding Member
Joined
Nov 2, 2015
Posts
739
Likes
29
Points
173
IMG_4575.jpgFargo area. 270 WSM full box of barnes and partial box of ELDX. Shoot pm if you want. No reasonable offer turned down.
 

Attachments

9E62F66A-E126-4EBD-9AD2-DC9F6CC0223B.jpg 082DEA15-D215-48FB-A80B-3412619F44FC.jpg
Last edited:

64Mustang

Founding Member
Founding Member
Joined
Aug 28, 2015
Posts
86
Likes
26
Points
113
IMG_4419.jpgIMG_4418.jpgI have the following for trade (multiples of each):
Hornady 7mm American Whitetail 139 gr ammo (3 left)
IMR 4451 powder (4 left)
H322 powder (1 left)
H380 powder (1 left)
H4350 powder (1 left)

CCI #350 Large pistol primers
CCI #400 Small Rifle primers
CCI #500 small Pistol primers

270 projectiles:
Hornady 110 gr HP (100 ct box)
Nosler accubond 100 gr (43)
Nosler Accubond 140 Gr (2 boxes of 50)
Nosler Accubond 150 Gr Long Range (140)
Nosler Accubond 175 Gr Long Range (100)


Looking for:
9mm FMJ ammo, 357 ammo, CCI200 or 250 large rifle primers, Federal 210 or 215 large rifle primers, 17 HMR ammo, 22 ammo, 22-250 ammo, 22 Cal VMax bullets 40 or 50 gr, and a few different rifle powders that I use like IMR 4350, IMR4895, H4895, IMR 4064, Reloder 17, Varget.
 
Last edited:


TFX 186

★★★★★ Legendary Member
Joined
Jan 25, 2016
Posts
839
Likes
132
Points
213
Location
NW ND
Sorry wrong thread to post this!

Guys, I need your help!
My boys are looking to get into reloading for handguns. I haven't used a progressive press and would like some insight on what I should get into. Would be reloading 9MM and 380 Auto and some 10MM. We don't need the very best as we are just getting started but we also will be splitting the costs to get into it so it would be more palatable for a better set up. We aren't major shooters yet but would probably shoot more as we load more.
We do some reloading for rifle hunting with a single stage RCBS press.
Thanks for your help!

Fish On!
 
Last edited:

MathewsZman

Founding Member
Founding Member
Joined
Apr 14, 2015
Posts
9,559
Likes
271
Points
358
Location
Harrold SD
I have 1900 rounds of these , 45 grain :
20210425_093248.jpg

- - - Updated - - -

400 rounds of center fire :
20210425_093626.jpg

- - - Updated - - -

And 500 rounds of :
20210425_093915.jpg
 

SDMF

Founding Member
Founding Member
Joined
Apr 24, 2015
Posts
10,908
Likes
620
Points
438
Guys, I need your help!
My boys are looking to get into reloading for handguns. I haven't used a progressive press and would like some insight on what I should get into. Would be reloading 9MM and 380 Auto and some 10MM. We don't need the very best as we are just getting started but we also will be splitting the costs to get into it so it would be more palatable for a better set up. We aren't major shooters yet but would probably shoot more as we load more.
We do some reloading for rifle hunting with a single stage RCBS press.
Thanks for your help!

Fish On!

Dillon 750 w/case-feeder is a superb machine. Give or take, ~800+ rounds/hr. Simple swap from 380-9MM, assuming you use the same brand primers for your loads it's just a die swap/powder recalc, or, even easier, have a toolhead/powder measurer set up for each and it's a 2-pin ~30sec swap.

Swapping primer sizes makes for a ~10Min swap-over, and, again, having a toolhead/powder-measurer set up for each chambering will save you significant time regarding setup/swapover.

The 550 is slower, but simpler and quicker to swap-over. I could be happy loading pistol cartridges on either the 550 or 750. I prefer to run rifle ammo (except 223's) on the 550. A 550 will run @ 350-400 rounds/hr.

FWIW, I'm 46 and still using the Dillon 550 my dad bought when I was in Jr. High. It's never been back to Dillon for anything, just clicks along doing it's thing so predictably it's mind-numbing. One caveat, ball/flake/spherical powders are your friend. "Extruded" powders can be maddening through a progressive powder measurer. Ball/flake/spherical will run +/- .1gn for hours on end. If I let the machine sit for a few hrs, I'll dump the 1st 2-3 powder charges right back into the powder hopper, then weigh the next few to make sure I'm spot on, then run again until I'm done.
 

Motohunter

Founding Member
Founding Member
Joined
May 31, 2015
Posts
310
Likes
27
Points
155
Location
Bismarck ND
Anyone have any 32 Winchester Special ammo they would be willing to part with? 1 box would be plenty.
 


Mac

Founding Member
Founding Member
Joined
Jun 19, 2015
Posts
30
Likes
0
Points
76
352080477_735272688598798_7082817501460774296_n.jpg352080477_735272688598798_7082817501460774296_n.jpgI have the following for trade (multiples of each):
Hornady 7mm American Whitetail 139 gr ammo (3 left)
IMR 4451 powder (4 left)
H322 powder (1 left)
H380 powder (1 left)
H4350 powder (1 left)

CCI #350 Large pistol primers
CCI #400 Small Rifle primers
CCI #500 small Pistol primers

270 projectiles:
Hornady 110 gr HP (100 ct box)
Nosler accubond 100 gr (43)
Nosler Accubond 140 Gr (2 boxes of 50)
Nosler Accubond 150 Gr Long Range (140)
Nosler Accubond 175 Gr Long Range (100)


Looking for:
9mm FMJ ammo, 357 ammo, CCI200 or 250 large rifle primers, Federal 210 or 215 large rifle primers, 17 HMR ammo, 22 ammo, 22-250 ammo, 22 Cal VMax bullets 40 or 50 gr, and a few different rifle powders that I use like IMR 4350, IMR4895, H4895, IMR 4064, Reloder 17, Varget.


I have 3 pounds of IMR 4350, and BLC2 I would consider trading for smaller rifle primers,
 


remm

Founding Member
Founding Member
Joined
May 18, 2015
Posts
1,127
Likes
59
Points
213
Location
Devils Lake
Looking for 6.5prc, 143gr eld-x or similar. New gun, just need enough to get er sighted in and ready to hunt by fall. I don't have much to trade but can pay cash or I have two good kidneys so can probably do without one of those, also have 3 kids and could probably get by with 2 :;:huh
 

Migrator Man

★★★★★ Legendary Member
Joined
Feb 3, 2016
Posts
3,961
Likes
22
Points
226
Found the motherload of powder today in WY, h4831sc, imr 4895, leverlution, hybrid 100v, any many others. Hopefully this is the beginning of the end!

Also seeing more handgun and .223 ammo but at crazy high prices!
 

sweeney

Founding Member
Founding Member
Joined
Apr 27, 2015
Posts
2,793
Likes
143
Points
313
Location
mandan
hopefully people stop panic buying and prices can return to normal soon.
 

LBrandt

★★★★★ Legendary Member
Joined
Apr 3, 2016
Posts
10,831
Likes
1,384
Points
498
Location
SE ND
Only way price is coming down is if people stop buying so that aint going to happen. If people are willing to pay the higher price the middle man is not going to change. Just going to get fatter. LB
 


Recent Posts

Friends of NDA

Top Posters of the Month

  • This month: 159
  • This month: 136
  • This month: 120
  • This month: 110
  • This month: 105
  • This month: 87
  • This month: 84
  • This month: 79
  • This month: 76
  • This month: 75
Top Bottom