What's new
Forums
Members
Resources
Whopper Club
Politics
Pics
Videos
Fishing Reports
Classifieds
Log in
Register
What's new
Search
Search
Search titles only
By:
Members
Resources
Whopper Club
Politics
Menu
Log in
Register
Install the app
Install
Forums
General
Recipes
Whole meat venison jerky
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="guywhofishes" data-source="post: 63809" data-attributes="member: 337"><p>great idea with the router - wish I had bought a thick cutting board and just done that ;:;banghead</p><p></p><p>BTW - no metal is exposed to the knife. The bolt heads are underneath and I tapped the license plate holder with 5/16 coarse threading. The bolts were cut just long enough so that the bolt ends sit well below the riding surface of the knife but grabs all the threads. The license plate holder has recessed screw holes on the front so that worked great for hiding metal from blade.</p><p></p><p>The back side of the license plate holder is flat/solid/continuous unlike most pressed/formed plate holders, so there's just the seam where it fits flush with the cutting board. A guy can lever up a little bit on the non-bolted side of plate holder to wash out under it but I experienced no solid bits getting underneath it - just blood. I bet some Goop would make it seamless but I probably won't hassle with it.</p><p></p><p>[ATTACH]3081[/ATTACH]</p><p>back side view - bolts sit lower than cushions so they don't scratch counter</p><p>I tightened the bolts gingerly with a pliers so as not to strip out the license plate holder holes that I had tapped </p><p></p><p>an alternative to elevator bolts would have been tapered head machine screws but I don't have a taper bit at home to make them sit flush underneath - so bought the goofy elevator bolts with the wide (but low profile) heads</p><p></p><p>again - a router would have made quick work of this chore - dangit</p></blockquote><p></p>
[QUOTE="guywhofishes, post: 63809, member: 337"] great idea with the router - wish I had bought a thick cutting board and just done that ;:;banghead BTW - no metal is exposed to the knife. The bolt heads are underneath and I tapped the license plate holder with 5/16 coarse threading. The bolts were cut just long enough so that the bolt ends sit well below the riding surface of the knife but grabs all the threads. The license plate holder has recessed screw holes on the front so that worked great for hiding metal from blade. The back side of the license plate holder is flat/solid/continuous unlike most pressed/formed plate holders, so there's just the seam where it fits flush with the cutting board. A guy can lever up a little bit on the non-bolted side of plate holder to wash out under it but I experienced no solid bits getting underneath it - just blood. I bet some Goop would make it seamless but I probably won't hassle with it. [ATTACH=CONFIG]3081._xfImport[/ATTACH] back side view - bolts sit lower than cushions so they don't scratch counter I tightened the bolts gingerly with a pliers so as not to strip out the license plate holder holes that I had tapped an alternative to elevator bolts would have been tapered head machine screws but I don't have a taper bit at home to make them sit flush underneath - so bought the goofy elevator bolts with the wide (but low profile) heads again - a router would have made quick work of this chore - dangit [/QUOTE]
Verification
What is the most common fish caught on this site?
Post reply
Recent Posts
Haze
Latest: Trip McNeely
1 minute ago
Northern Lights
Latest: Eatsleeptrap
Today at 3:28 PM
F
Representative Dockter
Latest: Fester
Today at 1:35 PM
Kristi Noem Dog Killer
Latest: Davey Crockett
Yesterday at 11:01 PM
Tailrace trout
Latest: svnmag
Yesterday at 9:54 PM
Sale
Marlin 30TK
Latest: svnmag
Yesterday at 9:16 PM
Velocitor V Stinger
Latest: svnmag
Yesterday at 9:09 PM
What are you listening to these days?
Latest: svnmag
Yesterday at 9:04 PM
This is what its all about
Latest: wslayer
Yesterday at 12:22 PM
Merino Undies
Latest: wslayer
Yesterday at 12:17 PM
Buying gold and silver.
Latest: grumster
Friday at 2:02 PM
SOLD
Elec Power Washer
Latest: Zogman
Friday at 1:26 PM
What boat ramp open in Bismark
Latest: Sluggo
Friday at 8:53 AM
No Mow May
Latest: lunkerslayer
Friday at 6:24 AM
Tammy Miller
Latest: Trip McNeely
Thursday at 11:23 PM
Wild Turkey
Latest: svnmag
Thursday at 9:26 PM
Best facebook page ever .
Latest: Davey Crockett
Thursday at 12:45 PM
Skinwalker Ranch
Latest: BrokenBackJack
Thursday at 11:28 AM
T
Wicked Waters Taxidermy
Latest: Traxion
Thursday at 11:19 AM
Electric Vehicles
Latest: svnmag
Wednesday at 9:07 PM
Friends of NDA
Forums
General
Recipes
Whole meat venison jerky
Top
Bottom