pull start a 90...

raider

Founding Member
Founding Member
Joined
Apr 22, 2015
Posts
3,397
Likes
45
Points
256
Location
williston
just going through some stuff in the garage today and ran across my new boat packet... laughed when i saw the pull start rope and threw it away... ya right, pull start a 90 horse...

but, why do they put it in there??? can you really pull start a motor that big...:;:huh
 


KDM

Founding Member
Founding Member
Joined
Apr 20, 2015
Posts
9,650
Likes
1,583
Points
563
Location
Valley City
Yep!! Watched a 100 lb man do it a couple dozen times on his "Rapido" while in Peru on the amazon river. A "Rapido" is a large 24 ft or so canoe with a flat transom. We were doing mosquito surveys and he was our transportation. He'd yank that rope and off we'd go. Some TOUGH folks on that river.
 

Ericb

Founding Member
Founding Member
Joined
May 19, 2015
Posts
3,200
Likes
85
Points
288
Location
Bismarck
I agree, I've always thought I should try using the one on my 135 just to know if I could in a emergency.
 

johnr

Founding Member
Founding Member
Joined
Apr 24, 2015
Posts
20,152
Likes
3,999
Points
813
Location
Dickinson
Yes I had a 75hp merc that the starter went out of, pull started rather easy actually.
 

ndlongshot

Founding Member
Founding Member
Joined
Apr 13, 2015
Posts
1,781
Likes
121
Points
268
I know its much smaller, but my old 50hp johnson is a breeze to pull start.
 


SDMF

Founding Member
Founding Member
Joined
Apr 24, 2015
Posts
10,980
Likes
708
Points
458
There's still only 1 piston firing at a time and it's still only ~10:1-10.5:1 compression. Much has to do with the gearing they can put on the pull start that'll allow enough travel of the crank to fire a few cylinders/pul.
 

raider

Founding Member
Founding Member
Thread starter
Joined
Apr 22, 2015
Posts
3,397
Likes
45
Points
256
Location
williston
thanks guys... would have never guessed... it will b going in the boat...

so, how big have you started with a rope???
 

guywhofishes

Founding Member
Founding Member
Joined
Apr 21, 2015
Posts
28,788
Likes
4,322
Points
958
Location
Faaargo, ND
I have started no larger than a 40 manually. But I swear I could start a 300 by hand if I saw a classic black anvilhead bearing down on me on Devils Lake. :eek:
 


Dad

Founding Member
Founding Member
Joined
May 29, 2015
Posts
184
Likes
2
Points
103
I tried pull start my 175 merc, and friend in boat tried as well (6'6' 325), not going to happen....not even close to being able to pull start it.
 


Allen

Founding Member
Founding Member
Joined
Apr 24, 2015
Posts
10,572
Likes
1,618
Points
638
Location
Lincoln, kinda...
Had a mid-80s 70 or 75 HP Mariner that pull started a HELL of a lot easier than my old 25 hp, mid 70s Johnson. The latter could wear you out in a hurry!
 

Obi-Wan

Founding Member
Founding Member
Joined
May 15, 2015
Posts
7,821
Likes
3,231
Points
808
Location
Bismarck
Had to pull start the 115 merc the first day I had it and used an old nylon stringer
 

Farmer

Founding Member
Founding Member
Joined
Jul 18, 2015
Posts
198
Likes
1
Points
108
Location
Cavalier County
A lot of snowmobile engines are over 100 horse and they pull start easily. The scareder ya is the easier they pull!
 

SupressYourself

Founding Member
Founding Member
Joined
Apr 21, 2015
Posts
2,017
Likes
437
Points
358
Location
Not where I'd like to be
I pulled a mid-80s 90HP Merc with a piece of anchor rope once. I believe that was only a 4 cyl though.
The 135 V6 Optimax may be a different story. I have a set of jumper cables that I have used to jump it from the trolling motor batteries when the starter battery was dead, but if the starter itself dies, I may be SOL...
 


Recent Posts

Friends of NDA

Top Posters of the Month

  • This month: 135
  • This month: 129
  • This month: 70
  • This month: 64
  • This month: 59
  • This month: 57
  • This month: 56
  • This month: 53
  • This month: 51
  • This month: 51
Top Bottom