Search results

  1. M

    Deck advice for guy

    I would build 12" oc,instead of 16"oc,alot have a minimum of 16"oc,but composite seems a little spongy,especially in hot weather.12 will give you a very solid deck.
  2. M

    Zeroing .22 LR

    Growing up my brother and me shared a Winchester 74 ,rear tube fed auto,don't know how many thousands of rounds went through that thing,used to spend our allowance on bricks of shells.Federal lightnings,spitfires,wildcats,yellow jackets,mini mags and Stingers. I don't think you could find...
  3. M

    Spotify Controversy

    I guess I'll check the box that says all three are dipshits.I am perfectly capable of forming my own thoughts and opinions and don't need a God damn podcast or song to sway me!!
  4. M

    Dusty Truck Box

    By pressurizing inside the box equal or slightly greater than depressurization it should not allow any significant amount in,we use similar techniques in weatherization using a blower door for diagnostic testing of homes.But I haven't run the test to see how much it varies at different...
  5. M

    Dusty Truck Box

    A fan inside the box pressuring would eliminate that issue,I am going to do some testing with a manometer to find what the level of depressurizaton is at various speeds to see how big of fan is needed to overcome it,had this on the back burner long enough.
  6. M

    Ice fishing,bibs and coat

    Striker Climate bibs and jacket for me,I have never been cold in it,most of the time its too warm for the jacket,so usuaslly wear a heavywieght carhartt hoodie instead,but i do have baselayers on also.I have drilled holes at the DL ice tourney and been on the ice til end of tourney in this...
  7. M

    Loaded Muzzleloader in or on motor vehicle?

    I would make sure you mark your ramrod,so that you know if you have a charge in the barrel or the charge has slid foward,just a good safety practice.I use a thin strip of the wifes crafting vinyl,easy to see and remove if you change loads. A buddys son shot a double load in the muzzy,thankfully...
  8. M

    Top Five Worst Deer Bullets?

    That guy should probably be throwing grenades!!
  9. M

    Inline Muzzleloader?

    Badger Ridge Industries in Michiagan will mod breech plugs.They reamed the flash channel to 1/8" and installed a .031 removable ventliner(flash hole),they did an excellent job on it,but still wasnt reliable ignition.In talking with them figured flash channel just too long on this plug.I think...
  10. M

    Inline Muzzleloader?

    Some guns shoot bh209 and some wont,due to breech plug design,length of flash channel,etc.If your gun will shoot it relialby,that is what I would definitely shoot,for the rest 777.You will know in the first shooting session if your gun will shoot it.Of the guns mentioned the TC should shoot...
  11. M

    Bow grip wrap or carbon bow?

    How about that self sticking silicon tape,the stuff used on ice fishing reels,buy it a whole lot cheaper in the hardware store,you could wrap it to your liking,comes off with no residue or harm to the finish,some insulating properties and wont come loose.I like the grips on my Hoyts so havent...
  12. M

    I Have this old Recurve

    I think most learn to gap shoot,looking down the arrow shaft and holding tip below your target,the gap will become smaller as distance increases,eventually becoming a subconsience action.When I would teach kids for a day at "get hooked on the outdoors",I changed it up a bit.I would have them...
  13. M

    Frosty Attic

    They do make covers for non ic(insulation compatible)fixtures or you can make your own to seal them.I work for a weatherization agency,some of the community action agencies in the state work(for profit)you might try them,insulation contractors should be able to thermal scan,maybe blower door,and...
  14. M

    Frosty Attic

    Lack of chutes is not the end of the world,especially in low pitched roofs,gable vents will give you good ventilation.I have seen ceiling line condensation due to improper chute installation.One house shot the cieling line with thermal camera 28 degrees,2ft down the wall 68,this was a -20...
  15. M

    Arrow Building

    You could spin test your broadheads,probably fine,or put your bow on a drawboard to check your cam timing,especially if it wont paper tune to a perfect bullet hole.
  16. M

    muzzleloader

    I could see a couple positives with the firesticks 1st being able to pull your charge without removing bullet,so you dont have to touch it off for storing 2nd primer sitting right on top of the charge should give great ignition. Interesting,but they havent reinvented the wheel,predict a big flop...
  17. M

    muzzleloader

    The type of propellant you use will depend on the type of gun you buy.Caplocks and flintlocks will probly be Goex blackpowder or pyrodex,Pyrodex would be my choice of the two,easier ignition and way cleaner.I use 777 in my Hawken,but have changed the nipple to a magspark,which allows for 209...
  18. M

    Compound bows for beginners

    I also recomend a trip to an archery shop,to get measured for drawlength,draw some bows,to get a feel for what you like,and if you do purchase you will have knowlegable staff to set you up.Once you have decided on a bow,I would put more $ into the rest and the release vs sight,stabilizesr...
  19. M

    Ice house Door

    I would look at a mobile home door,you will find much closer to the size you need,and just have to screw onto ro with pole barn screws,28" width is gonna be tough to find,30 is tough.Might have to make wider. Cut down steel doors never last,but taking off the top is better,just alot more...
  20. M

    ames River Sportsmans Club - Annual 3-D Archery Shoot - Lake LaMoure

    This is a very nice course and enjoyable shoot,Hoping to make it!!

Recent Posts

Friends of NDA

Top Bottom